Why shop with us? Brand Names You Can Trust. Radio(s)/Reciver(s). Add our store to your favorite stores and receive our exclusive emails about new items and special promotions! Brand New in Factory Packaging. In Stock Ships Within 24hrs. Putting the X in Extreme! The Mamba Micro X Crawler edition is our latest offering for the crawling crowd. We have taken our new 1406 low kv crawler motors and paired it with the lightweight, small footprint Mamba Micro X ESC. This combo is ideal for low speed crawling or trail running in vehicles weighing up to 8lbs on 2s or 3s; it can also be used in slightly more aggressive setups like rock racing and extended hill climbing on vehicles up to 4lbs. If you’re looking for a more aggressive setup in a heavier rig, like rock racing and extended hill climbing, we recommend you run the Mamba X ESC with the same motor. Your ESC will come with our new V2.02 firmware that has been enhanced for rock crawling and sensored operation. Use of an external BEC is recommended if running a high power or digital servo. Mamba Micro X features the addition of a new, programmable Auxiliary Wire that allows you to make on-the-go adjustments to several settings such as torque control, and max throttle, and fine-tune the performance of your ESC right from the transmitter using an auxiliary channel on the receiver. The AUX wire function is disabled by default but is programmable via Castle Link. Once you have programmed the functionality of the AUX wire, that setting can then be adjusted on-the-go from a compatible transmitter. Try out the brand new Crawler Mode for incredible versatility! Real-time data such as ESC temperature, voltages, and RPM can be monitored to ensure performance advantages and spare you the unknown parameters that all R/C enthusiasts experience at some point. Telemetry data provides another level of protection and can increase performance. Crawler Edition Mamba Micro X w/solder posts. 210mm length sensor wire (for sensored operation). Castle Sensor Harness adapter. Coupon for free Castle Link USB adapter. Driver’s Ed and Quick Start Guides. Electronic Speed Control (ESC). Input Voltage Range: MIN: 2S LiPo. MAX: 3S LiPo (12.6V). BEC Specifications: Adjustable: 5.5V or 7.5V (2A Peak), default 5.5V. Note: Use of external BEC is recommended if using a high torque/speed digital servo; the CC BEC or CC BEC 2.0 Waterproof are recommended. Operating Environment: Waterproof design allows for use in nearly any environment. Reversible: Yes, but can be disabled for racing. On/Off Switch: Yes, waterproof. Size: Length: 1.6 (41mm). Width: 0.75 (19mm). Height: 1.1 (28mm). Weight (without wires): 1.20 oz. Connectors: 4mm male Castle Bullet Connectors attached to replaceable 16 gauge wire; includes Castle sensor harness. Items Needed for Operation: Battery Connector required, Castle 4mm polarized Connectors, Deans Ultra Plugs, or Traxxas Power Connect are recommended. Recommended battery capacity is at least 1500mAh and 25C. You must solder the connector to the wires on the ESC. See Items Needed for Operation for recommendations. Application Guidelines: Low speed crawling or trail running in vehicles weighing up to 8lbs on 2s or 3s LiPo; can also be used in vehicles up to 4lbs for extended hill climbing and rock racing. We also pair the same motor with the larger, more powerful Mamba X ESC for more aggressive setups and driving. Recommended Vehicle Weight: 8lbs when used for low speed/moderate driving style; 4lbs for more aggressive driving styles. Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free link included in package) and freely downloadable Castle Link Windows software. Telemetry Link Capable: Yes. Tech Notes: Water Resistant Design: The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommended applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to this document for running and maintaining motors in wet environments. Input Voltage Range: 2S-3S LiPo. Size: Length: 49.5mm. Weight (w/wires): 197 g / 6.9oz. Shaft Size: Length: 15mm. Diameter: 1/8 (3.17mm). Optional 5mm rotor replacement available. Cooling Fan: Optional – Coming Soon. Connectors: 4mm male Castle Bullet Connectors attached to replaceable 13 gauge wire; includes 210mm length sensored wire. Application Guidelines: Ideal for 1:10 scale low speed rock crawlers/trail runners on 2S or 3S weighing less than 8lbs; can also be used in vehicles up to 4lbs for extended hill climbing and rock racing. Recommended Vehicle Weight: 8lbs when used for low speed/moderate driving style like rock crawling and trail running. 4lbs for more racing and aggressive driving styles. Running modes: SMARTSENSE, Sensored, Sensorless with Castle sensored capable ESCs. Water Resistant Design: The sensor board is coated with silicone conformal coating to protect the sensors from moisture. Please note: I will not put less amount on custom papers, so please don’t ask. You can return any item in Brand New/unopened condition (within 14 days). The item “Castle Creations Mamba Micro X 12.6V ESC with1406-2850KV Sensored Motor” is in sale since Tuesday, October 15, 2019. This item is in the category “Toys & Hobbies\Radio Control & Control Line\RC Model Vehicle Parts & Accs\Engine, Exhaust & Fuel Systems\Electric Motors”. The seller is “power_hobby” and is located in Mahwah, New Jersey. This item can be shipped to United States, all countries in Europe, Canada, Japan, Australia.

• Brand: Castle Creations
• MPN: 010-0162-03
• Compatible Vehicle Type: Cars, Trucks & Motorcycles
• upc: 819326010460